Flexispot Standing Desk Review …Computer Riser & Flexispot & Amazon…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are very little, here are a few features that I wasn’t always a huge fan of:
The package that the desk was available in was heavy, so bringing it inside was a group effort, however this is just a repercussion of how tough the Flexispot is.
The convenient cable tray was a bit confusing to install. In the end, you eventually slip it under screws, which wasn’t very clear from the instructions.
You will need to purchase an anti-fatigue mat to stay comfy, but this is an excellent concept for any standing desks, so I can’t fault Flexispot for that.
When it arrived and I saw how heavy it was, I was both fired up (given that this meant it was going to be tough) and likewise a little reluctant (due to the fact that we all understand how much of a difficulty putting together furnishings can be).
The good news is, with the help of an educational YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old child, with some supervision from me, from start to finish. The only problem I have with assembly was the cable television tray, which I discovered wasn’t discussed well in the instructions.
Once assembled, I love the smooth appearance of this desk. I’m confident any of the many diverse surfaces that it is available in would look excellent in any workplace, and the adjustable width makes it simple to fit it in even the tiniest of office.
The quiet operation and height memory settings make it easy, effective, and peaceful to change between sitting and standing as often times as you want throughout the day.
Last but not least, this desk is sturdy. It can hold up to 335 lbs even while in operation, so if you have a large desktop (or wish to take a nap on it for some reason) it has you covered. It will likewise evenly disperse weight no matter how out of balance the weight you put on it is, it won’t wiggle or wobble.
in that video is pretty kitted out as the desk we’re looking at today is pretty basic I attempted to get as near that as I could on uplifts site with similar configurations the flexi area desk we’re taking a look at today will run you about four hundred and 10 dollars versus six hundred and fifty for a comparable desk from uplift I try to get as close as possible with the uplift design is in fact five inches longer however you can do a lot with five inches boom yes now for transparency flexi spot did send this desk out for evaluation however as you need to understand by now does not affect my evaluation in any way the desktop here is 55 inches wide 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering until completion of April at the earliest the desktop is an inch thick but it’s this standard laminate as you can potentially get doing not have even any cable television grommets for pass through the outdoors container
for the desktop was not harmed in any way which is absolutely bizarre since I could shoot a 30-second b-roll montage of just the damage and defects on this desktop scuffed scraped pitted simply very rough male if I had actually bought this I ‘d have been on the phone with client service instantly they did likewise managed to miss drilling the pilot holes where you can attach the control box to the desktop a great deal of needing to do that myself without inadvertently drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was actually quite uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cables running to it from each element to support motorized function unusually absolutely where any kind of cable television management products whatsoever the frame on this unit is a single motor double stage style versus the dual motor three-stage design that comes requirement with the uplift desk this can be upgraded as well to both the dual phase double motor and a three-stage dual motor which pushes the cost of the desk up
an extra 70 dollars the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per second the height can vary from just under 28 inches to just over forty seven point six inches so a max I ‘d it is more than high enough even for me and I remain at 6 foot for this design does come basic with the control panel that enables up-and-down movement plus three memory areas with an LED readout to inform you the desk height the single motor style utilizes this drive shaft assembly which has to be changed as the width of the desk is changed the motor operation itself while it might be slow is extremely peaceful as in barely audible this outside a rate would be the one benefit I would give this unit over the uplift desk and I wish to be careful here since this isn’t a hit piece this desk is 240 dollars less expensive than the similar uplift model over 35% more affordable even if you update this flexi spot test to the double motor three-stage design it still comes in a hundred and seventy dollars cheaper than the uplift but cheaper doesn’t imply low-cost this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is strong even if max height I’ll definitely give it that but the lateral stability of this desk the horizontal motion at this cost point it’s unacceptable it’s add fuel to the fire here they consist of a little safety baffle this little steel piece that mounts to the frame and covers a portion of this rotating driveshaft when
this desk sees any lateral movement at all the drive shaft strikes the noise and this baffle is definitely shocking to top things off I chose to add rolling casters to this desk this was a $30 upgrade and 2 of those 4 casters arrived harmed too my plan for this desk at this point is to lose the desk top and included entirely and change it with a white laminate lemon table from Ikea and use it as an adjustable photo table which you can’t do this frame will accommodate desktops up to 63 inches wide and 31 and a half inches deep so this will roll around the studio make it simpler to film items without having to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift initially that is an investment in quality workplace furnishings that will last you this at finest feels like a cheaper imitation of that it simply doesn’t feel quality and the difference in between this desk and my primary desk is night and day do do not hesitate to have a look at their site as well which also feels strangely similar to among their competitors there’s a wealth of devices you can get for the flexi area desk as much as and consisting of a foot massager and even a fixed exercise bike and I might invest another 10 minutes of our precious time covering numerous choices and devices I might however I believe I’m happier that they just sent out a standard desk due to the fact that as a basic desk I’m not a fan of the quality control at this cost point and I don’t believe slapping on a lot of extras is the move when the core product isn’t what it ought to be they do offer a 30-day trial if you’re just morbidly curious and they guarantee their desks for 3 years extremely desk is 5 years and uplift desk is 7 years if you are Computer Riser & Flexispot & Amazon
in the market for a sit-stand desk they’re amazing mine’s been a life changer for me both in regards to video gaming and efficiency however I would invest the extra money it’s gon na require to enter into a higher end manufacturer like uplift desk or really desk and I have not personally utilized really desk items so I can’t speak on it however their credibility is excellent huge thanks to flexi spot for sending this out for evaluation sadly I can not advise this system and for the record I’m a hundred percent sure they would have happily replaced the parts that I had an issue with viewing as how both the desktop and the casters showed up damaged however from a client perspective you ‘d most likely be actually thrilled to get this in