Flexispot Standing Desk Review …Flexispot 35 Riser…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are minimal, here are a few features that I wasn’t necessarily a substantial fan of:
The bundle that the desk was available in was heavy, so bringing it inside was a group effort, however this is simply a repercussion of how durable the Flexispot is.
The convenient cable television tray was a little bit complicated to set up. In the end, you eventually slip it under screws, which wasn’t very clear from the instructions.
You will require to buy an anti-fatigue mat to stay comfy, but this is a good concept for any standing desks, so I can’t fault Flexispot for that.
When it got here and I saw how heavy it was, I was both fired up (considering that this suggested it was going to be strong) and also a little reluctant (because all of us know how much of a challenge assembling furniture can be).
Luckily, with the help of an instructional YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old child, with some supervision from me, from start to finish. The only problem I have with assembly was the cable tray, which I found wasn’t described well in the guidelines.
Once put together, I love the streamlined look of this desk. I’m positive any of the many varied surfaces that it is available in would look great in any office, and the adjustable width makes it simple to fit it in even the smallest of office.
The quiet operation and height memory settings make it easy, efficient, and peaceful to change in between sitting and standing as often times as you want throughout the day.
This desk is tough. It can hold up to 335 lbs even while in operation, so if you have a significant desktop computer (or want to take a nap on it for some reason) it has you covered. It will also evenly distribute weight no matter how unbalanced the weight you put on it is, it will not wiggle or wobble.
in that video is quite kitted out as the desk we’re looking at today is pretty standard I tried to get as close to that as I could on uplifts site with comparable setups the flexi spot desk we’re looking at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift design is actually 5 inches longer but you can do a lot with five inches boom yes now for transparency flexi area did send this desk out for review but as you must know by now does not impact my evaluation in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not delivering till the end of April at the earliest the desktop is an inch thick however it’s this fundamental laminate as you can potentially get lacking even any cable grommets for go through the outside carton
for the desktop was not damaged in any way which is absolutely unusual since I could shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted simply very rough man if I had actually bought this I ‘d have been on the phone with client service immediately they did also handled to miss out on drilling the pilot holes where you can connect the control box to the desktop a great deal of having to do that myself without accidentally drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was really pretty uncomplicated the whole thing came together in about 45 minutes and despite the fact that there’s cables running to it from each part to support motorized function strangely absolutely where any kind of cable management materials whatsoever the frame on this system is a single motor dual stage style versus the dual motor three-stage design that comes standard with the uplift desk this can be updated too to both the dual phase double motor and a three-stage dual motor which pushes the cost of the desk up
an extra 70 dollars the frame is created for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can range from just under 28 inches to simply over forty 7 point 6 inches so a max I ‘d it is more than high adequate even for me and I remain at 6 foot for this design does come basic with the control panel that enables up-and-down movement plus three memory areas with an LED readout to inform you the desk height the single motor design uses this drive shaft assembly which needs to be changed as the width of the desk is changed the motor operation itself while it might be slow is really peaceful as in barely audible this outside a cost would be the one benefit I would provide this system over the uplift desk and I want to beware here since this isn’t a hit piece this desk is 240 dollars less expensive than the comparable uplift design over 35% more affordable even if you upgrade this flexi area test to the dual motor three-stage design it still can be found in a hundred and seventy dollars cheaper than the uplift however cheaper does not suggest low-cost this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is strong even if max height I’ll definitely offer it that but the lateral stability of this desk the horizontal motion at this price point it’s undesirable it’s add insult to injury here they include a little security baffle this little steel piece that installs to the frame and covers a portion of this rotating driveshaft when
this desk sees any lateral movement at all the drive shaft hits this baffle and the sound is definitely frustrating to top things off I decided to include rolling casters to this desk this was a $30 upgrade and 2 of those 4 casters arrived harmed too my plan for this desk at this point is to lose the desk top and featured completely and change it with a white laminate lemon table from Ikea and utilize it as an adjustable photo table which you can’t do this frame will accommodate desktops up to 63 inches wide and 31 and a half inches deep so this will roll around the studio make it easier to film products without having to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is an investment in quality workplace furniture that will last you this at best feels like a more affordable replica of that it simply does not feel quality and the distinction in between this desk and my main desk is night and day do do not hesitate to check out their website also which also feels strangely comparable to among their competitors there’s a wealth of accessories you can get for the flexi area desk as much as and including a foot massager and even a stationary stationary bicycle and I might invest another 10 minutes of our precious time covering numerous choices and accessories I might however I believe I’m better that they just sent out a standard desk due to the fact that as a basic desk I’m not a fan of the quality control at this price point and I don’t believe slapping on a lot of extras is the move when the core item isn’t what it must be they do provide a 30-day trial if you’re simply morbidly curious and they guarantee their desks for 3 years really desk is 5 years and uplift desk is seven years if you are Flexispot 35 Riser
in the market for a sit-stand desk they’re amazing mine’s been a life changer for me both in regards to video gaming and efficiency however I would spend the money it’s gon na take to get into a greater end maker like uplift desk or extremely desk and I have not personally utilized extremely desk products so I can’t speak on it however their reputation is excellent huge thanks to flexi spot for sending this out for evaluation sadly I can not recommend this unit and for the record I’m a hundred percent sure they would have gladly replaced the parts that I had a problem with viewing as how both the desktop and the casters showed up damaged however from a customer standpoint you ‘d probably be actually thrilled to get this in