Flexispot Standing Desk Review …Flexispot 35\” Wide Platform Height Adjustable Standing Desk Riser, Reviews…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are very little, here are a couple of functions that I wasn’t always a big fan of:
The plan that the desk was available in was heavy, so bringing it inside was a group effort, however this is just an effect of how durable the Flexispot is.
The hassle-free cable tray was a little bit confusing to set up. In the end, you eventually slip it under screws, which wasn’t very clear from the guidelines.
You will require to buy an anti-fatigue mat to stay comfortable, however this is an excellent idea for any standing desks, so I can’t fault Flexispot for that.
When it showed up and I saw how heavy it was, I was both thrilled (considering that this implied it was going to be durable) and also a little reluctant (due to the fact that we all understand how much of a challenge assembling furniture can be).
The good news is, with the help of a training YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some guidance from me, from start to finish. The only hang-up I have with assembly was the cable tray, which I discovered wasn’t discussed well in the guidelines.
When assembled, I like the smooth look of this desk. I’m confident any of the many varied surfaces that it is available in would look fantastic in any office, and the adjustable width makes it simple to fit it in even the smallest of home offices.
The quiet operation and height memory settings make it simple, effective, and quiet to change between sitting and standing as sometimes as you desire throughout the day.
Finally, this desk is strong. It can hold up to 335 pounds even while in operation, so if you have a hefty desktop (or want to rest on it for some reason) it has you covered. It will likewise uniformly distribute weight no matter how out of balance the weight you put on it is, it won’t wiggle or wobble.
because video is quite kitted out as the desk we’re looking at today is quite standard I tried to get as close to that as I could on uplifts website with comparable configurations the flexi spot desk we’re taking a look at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a comparable desk from uplift I try to get as close as possible with the uplift model is in fact 5 inches longer however you can do a lot with five inches boom yes now for openness flexi spot did send this desk out for evaluation however as you must know by now doesn’t affect my evaluation in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering up until completion of April at the earliest the desktop is an inch thick however it’s this fundamental laminate as you can potentially get doing not have even any cable grommets for travel through the outside container
for the desktop was not damaged in any way which is utterly strange because I might shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted simply super rough man if I had actually bought this I ‘d have been on the phone with client service immediately they did also managed to miss out on drilling the pilot holes where you can connect the control box to the desktop a lot of having to do that myself without unintentionally drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was in fact pretty straightforward the whole thing came together in about 45 minutes and despite the fact that there’s cables running to it from each part to support motorized function unusually definitely where any kind of cable television management products whatsoever the frame on this unit is a single motor dual stage design versus the double motor three-stage style that comes requirement with the uplift desk this can be upgraded as well to both the double phase dual motor and a three-stage double motor which presses the expense of the desk up
an additional 70 dollars the frame is created for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can vary from just under 28 inches to simply over forty 7 point six inches so a max I ‘d it is more than tall enough even for me and I remain at 6 foot for this design does come basic with the control panel that allows for up-and-down motion plus three memory spots with an LED readout to tell you the desk height the single motor design utilizes this drive shaft assembly which has to be adjusted as the width of the desk is changed the motor operation itself while it might be slow is very quiet as in barely audible this outside a rate would be the one advantage I would offer this system over the uplift desk and I wish to take care here since this isn’t a hit piece this desk is 240 dollars less expensive than the comparable uplift design over 35% more affordable even if you upgrade this flexi spot test to the dual motor three-stage design it still can be found in a hundred and seventy dollars less expensive than the uplift but less expensive does not suggest cheap this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is strong even if max height I’ll definitely give it that however the lateral stability of this desk the horizontal movement at this rate point it’s unacceptable it’s rub salt in the wound here they consist of a little safety baffle this little steel piece that installs to the frame and covers a portion of this turning driveshaft when
this desk sees any lateral motion at all the drive shaft hits the sound and this baffle is absolutely infuriating to top things off I decided to add rolling casters to this desk this was a $30 upgrade and two of those four casters arrived harmed as well my plan for this desk at this moment is to lose the desk top and included entirely and change it with a white laminate lemon table from Ikea and use it as an adjustable photo table which you can’t do this frame will accommodate desktops approximately 63 inches large and 31 and a half inches deep so this will roll around the studio make it much easier to movie products without having to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is an investment in quality office furnishings that will last you this at best seems like a more affordable replica of that it just does not feel quality and the difference in between this desk and my primary desk is night and day do do not hesitate to check out their website too which also feels eerily comparable to among their competitors there’s a wealth of accessories you can get for the flexi area desk approximately and including a foot massager and even a stationary exercise bike and I might spend another 10 minutes of our precious time covering numerous options and devices I might but I think I’m happier that they just sent out a standard desk because as a standard desk I’m not a fan of the quality assurance at this price point and I don’t believe slapping on a bunch of additionals is the relocation when the core item isn’t what it must be they do use a 30-day trial if you’re simply morbidly curious and they warranty their desks for three years really desk is 5 years and uplift desk is seven years if you are Flexispot 35\” Wide Platform Height Adjustable Standing Desk Riser, Reviews
in the market for a sit-stand desk they’re incredible mine’s been a life changer for me both in terms of gaming and efficiency but I would spend the extra money it’s gon na require to enter a greater end producer like uplift desk or very desk and I have not personally used very desk products so I can’t speak on it however their credibility is excellent big thanks to flexi area for sending this out for evaluation unfortunately I can not advise this system and for the record I’m a hundred percent sure they would have gladly changed the parts that I had a problem with viewing as how both the desktop and the casters showed up harmed but from a customer standpoint you ‘d most likely be truly excited to get this in