Flexispot Standing Desk Evaluation …Flexispot Fm3 47…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are minimal, here are a couple of features that I wasn’t always a big fan of:
The bundle that the desk can be found in was heavy, so bringing it inside was a group effort, but this is simply an effect of how durable the Flexispot is.
The hassle-free cable television tray was a little bit complicated to install. In the end, you eventually slip it under screws, which wasn’t very clear from the directions.
You will need to purchase an anti-fatigue mat to stay comfy, but this is a great idea for any standing desks, so I can’t fault Flexispot for that.
When it arrived and I saw how heavy it was, I was both ecstatic (because this meant it was going to be sturdy) and also a little hesitant (because we all know how much of a difficulty assembling furniture can be).
Thankfully, with the help of an educational YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some guidance from me, from start to finish. The only problem I have with assembly was the cable tray, which I found wasn’t described well in the instructions.
As soon as assembled, I like the sleek appearance of this desk. I’m confident any of the many diverse finishes that it is available in would look terrific in any workplace, and the adjustable width makes it simple to fit it in even the smallest of office.
The quiet operation and height memory settings make it easy, efficient, and quiet to switch between sitting and standing as sometimes as you desire throughout the day.
This desk is sturdy. It can hold up to 335 pounds even while in operation, so if you have a significant desktop computer (or want to take a nap on it for some reason) it has you covered. It will also uniformly disperse weight no matter how out of balance the weight you place on it is, it will not wobble or wiggle.
because video is pretty kitted out as the desk we’re looking at today is quite basic I attempted to get as close to that as I could on uplifts site with comparable configurations the flexi spot desk we’re taking a look at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a similar desk from uplift I attempt to get as close as possible with the uplift design is actually 5 inches longer however you can do a lot with five inches boom yes now for openness flexi area did send this desk out for evaluation but as you ought to understand by now doesn’t impact my review in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping up until completion of April at the earliest the desktop is an inch thick however it’s this standard laminate as you can perhaps get lacking even any cable television grommets for pass through the outdoors carton
for the desktop was not damaged in any way which is absolutely strange because I could shoot a 30-second b-roll montage of simply the damage and flaws on this desktop scuffed scraped pitted just very rough man if I had actually purchased this I ‘d have been on the phone with client service right away they did also handled to miss drilling the pilot holes where you can connect the control box to the desktop a lot of needing to do that myself without inadvertently drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was really quite straightforward the entire thing came together in about 45 minutes and despite the fact that there’s cable televisions running to it from each part to support motorized function unusually absolutely where any type of cable television management products whatsoever the frame on this system is a single motor double phase style versus the dual motor three-stage design that comes standard with the uplift desk this can be upgraded as well to both the dual stage double motor and a three-stage double motor which pushes the expense of the desk up
an extra 70 bucks the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per second the height can vary from simply under 28 inches to just over forty 7 point six inches so a max I ‘d it is more than high sufficient even for me and I stay at 6 foot for this design does come standard with the control panel that allows for up-and-down movement plus three memory spots with an LED readout to inform you the desk height the single motor design utilizes this drive shaft assembly which needs to be adjusted as the width of the desk is adjusted the motor operation itself while it might be sluggish is really peaceful as in barely audible this outside a cost would be the one advantage I would offer this system over the uplift desk and I want to take care here due to the fact that this isn’t a hit piece this desk is 240 dollars less expensive than the similar uplift design over 35% cheaper even if you upgrade this flexi spot test to the dual motor three-stage style it still comes in a hundred and seventy dollars cheaper than the uplift however more affordable doesn’t indicate cheap this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is solid even if max height I’ll certainly provide it that however the lateral stability of this desk the horizontal movement at this cost point it’s unacceptable it’s add fuel to the fire here they consist of a little security baffle this little steel piece that installs to the frame and covers a part of this rotating driveshaft when
this desk sees any lateral movement at all the drive shaft hits this baffle and the noise is definitely frustrating to top things off I chose to include rolling casters to this desk this was a $30 upgrade and 2 of those four casters showed up damaged too my plan for this desk at this moment is to lose the desk top and came with completely and replace it with a white laminate lemon table from Ikea and utilize it as an adjustable image table which you can’t do this frame will accommodate desktops approximately 63 inches wide and 31 and a half inches deep so this will roll around the studio make it easier to movie products without having to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift first that is an investment in quality workplace furniture that will last you this at best seems like a more affordable imitation of that it simply doesn’t feel quality and the difference between this desk and my primary desk is night and day do feel free to take a look at their site also which also feels strangely similar to one of their rivals there’s a wealth of accessories you can get for the flexi area desk approximately and including a foot massager and even a fixed stationary bicycle and I might spend another 10 minutes of our valuable time covering numerous choices and devices I might but I believe I’m better that they only sent out a fundamental desk since as a basic desk I’m not a fan of the quality control at this cost point and I do not think slapping on a lot of extras is the move when the core item isn’t what it should be they do use a 30-day trial if you’re just morbidly curious and they warranty their desks for 3 years really desk is five years and uplift desk is seven years if you are Flexispot Fm3 47
in the market for a sit-stand desk they’re incredible mine’s been a life changer for me both in terms of gaming and performance however I would invest the additional money it’s gon na take to get into a higher end producer like uplift desk or very desk and I haven’t personally utilized really desk products so I can’t speak on it however their reputation is very good big thanks to flexi area for sending this out for evaluation regrettably I can not recommend this unit and for the record I’m a hundred percent sure they would have gladly changed the parts that I had a problem with viewing as how both the desktop and the casters got here harmed however from a customer perspective you ‘d most likely be really delighted to get this in