Flexispot Standing Desk Evaluation …Flexispot M2 35″…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are very little, here are a few functions that I wasn’t always a huge fan of:
The plan that the desk was available in was heavy, so bringing it inside was a group effort, however this is simply a consequence of how tough the Flexispot is.
The convenient cable tray was a bit confusing to set up. In the end, you eventually slip it under screws, which wasn’t extremely clear from the directions.
You will require to purchase an anti-fatigue mat to stay comfortable, however this is a great concept for any standing desks, so I can’t fault Flexispot for that.
When it got here and I saw how heavy it was, I was both ecstatic (given that this meant it was going to be sturdy) and also a little hesitant (because we all know just how much of a challenge assembling furniture can be).
The good news is, with the help of an educational YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some guidance from me, from start to finish. The only problem I have with assembly was the cable tray, which I found wasn’t described well in the directions.
As soon as assembled, I like the streamlined look of this desk. I’m confident any of the many varied surfaces that it comes in would look terrific in any office, and the adjustable width makes it simple to fit it in even the tiniest of home offices.
The peaceful operation and height memory settings make it easy, efficient, and quiet to switch in between sitting and standing as often times as you want throughout the day.
Last but not least, this desk is durable. It can hold up to 335 lbs even while in operation, so if you have a hefty desktop computer (or wish to take a nap on it for some reason) it has you covered. It will likewise evenly disperse weight no matter how unbalanced the weight you place on it is, it will not wobble or wiggle.
because video is quite kitted out as the desk we’re looking at today is pretty basic I tried to get as close to that as I might on uplifts website with equivalent configurations the flexi spot desk we’re looking at today will run you about four hundred and ten dollars versus 6 hundred and fifty for a comparable desk from uplift I attempt to get as close as possible with the uplift model is in fact 5 inches longer but you can do a lot with five inches boom yes now for openness flexi spot did send this desk out for evaluation but as you should understand by now doesn’t impact my evaluation in any way the desktop here is 55 inches wide 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not delivering till completion of April at the earliest the desktop is an inch thick but it’s this fundamental laminate as you can possibly get doing not have even any cable television grommets for go through the outdoors carton
for the desktop was not harmed in any way which is entirely unusual because I could shoot a 30-second b-roll montage of just the damage and flaws on this desktop scuffed scraped pitted simply super rough male if I had actually purchased this I ‘d have been on the phone with customer service right away they did likewise handled to miss out on drilling the pilot holes where you can connect the control box to the desktop a lot of having to do that myself without accidentally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was in fact pretty uncomplicated the whole thing came together in about 45 minutes and despite the fact that there’s cables going to it from each element to support motorized function oddly absolutely where any sort of cable television management products whatsoever the frame on this system is a single motor double phase design versus the dual motor three-stage style that comes standard with the uplift desk this can be updated also to both the dual phase double motor and a three-stage dual motor which presses the expense of the desk up
an extra 70 bucks the frame is created for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can vary from just under 28 inches to simply over forty 7 point six inches so a max I ‘d it is more than high sufficient even for me and I stay at 6 foot for this design does come basic with the control board that permits up-and-down movement plus 3 memory spots with an LED readout to tell you the desk height the single motor design uses this drive shaft assembly which has to be adjusted as the width of the desk is changed the motor operation itself while it might be sluggish is very peaceful as in barely audible this outside a rate would be the one benefit I would give this system over the uplift desk and I want to beware here because this isn’t a hit piece this desk is 240 dollars more affordable than the similar uplift model over 35% less expensive even if you update this flexi spot test to the dual motor three-stage design it still can be found in a hundred and seventy dollars cheaper than the uplift but more affordable doesn’t imply low-cost this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is solid even if max height I’ll certainly give it that however the lateral stability of this desk the horizontal movement at this rate point it’s inappropriate it’s rub salt in the wound here they consist of a little safety baffle this little steel piece that mounts to the frame and covers a portion of this turning driveshaft when
this desk sees any lateral movement at all the drive shaft hits this baffle and the sound is absolutely shocking to top things off I decided to include rolling casters to this desk this was a $30 upgrade and two of those four casters got here harmed also my plan for this desk at this moment is to lose the desk top and featured entirely and change it with a white laminate lemon table from Ikea and utilize it as an adjustable image table which you can’t do this frame will accommodate desktops approximately 63 inches broad and 31 and a half inches deep so this will roll around the studio make it simpler to film items without having to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift first that is a financial investment in quality office furnishings that will last you this at finest feels like a less expensive replica of that it just does not feel quality and the distinction in between this desk and my primary desk is night and day do feel free to have a look at their website as well which likewise feels strangely comparable to among their rivals there’s a wealth of accessories you can get for the flexi spot desk up to and consisting of a foot massager and even a fixed exercise bike and I might invest another 10 minutes of our valuable time covering different options and accessories I could however I believe I’m better that they just sent out a standard desk due to the fact that as a standard desk I’m not a fan of the quality control at this rate point and I do not believe slapping on a bunch of bonus is the move when the core item isn’t what it ought to be they do provide a 30-day trial if you’re just morbidly curious and they service warranty their desks for 3 years extremely desk is five years and uplift desk is seven years if you are Flexispot M2 35″
in the market for a sit-stand desk they’re fantastic mine’s been a life changer for me both in regards to gaming and efficiency but I would spend the additional money it’s gon na take to enter into a greater end maker like uplift desk or extremely desk and I haven’t personally used extremely desk items so I can’t speak on it however their reputation is great big thanks to flexi spot for sending this out for evaluation unfortunately I can not advise this system and for the record I’m a hundred percent sure they would have gladly changed the parts that I had an issue with seeing as how both the desktop and the casters arrived damaged but from a client viewpoint you ‘d probably be truly delighted to get this in