Flexispot Standing Desk Review …Flexispot M4 Xl Corner Sit-stand Desktop Work Station…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are very little, here are a few functions that I wasn’t necessarily a big fan of:
The bundle that the desk was available in was heavy, so bringing it inside was a group effort, but this is just an effect of how strong the Flexispot is.
The practical cable tray was a little bit complicated to set up. In the end, you ultimately slip it under screws, which wasn’t extremely clear from the guidelines.
You will require to buy an anti-fatigue mat to remain comfortable, but this is a great idea for any standing desks, so I can’t fault Flexispot for that.
When it got here and I saw how heavy it was, I was both thrilled (because this implied it was going to be durable) and also a little reluctant (since all of us know how much of an obstacle assembling furniture can be).
Luckily, with the help of an instructional YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some supervision from me, from start to finish. The only problem I have with assembly was the cable tray, which I found wasn’t explained well in the directions.
Once put together, I like the streamlined look of this desk. I’m positive any of the many varied finishes that it is available in would look great in any workplace, and the adjustable width makes it easy to fit it in even the smallest of office.
The peaceful operation and height memory settings make it easy, effective, and quiet to switch between sitting and standing as often times as you desire throughout the day.
Last but not least, this desk is tough. It can hold up to 335 lbs even while in operation, so if you have a large desktop computer (or wish to sleep on it for some reason) it has you covered. It will likewise equally disperse weight no matter how out of balance the weight you put on it is, it will not wobble or wiggle.
because video is quite kitted out as the desk we’re looking at today is quite fundamental I tried to get as near that as I could on uplifts website with equivalent configurations the flexi spot desk we’re taking a look at today will run you about four hundred and ten dollars versus 6 hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift model is in fact five inches longer but you can do a lot with five inches boom yes now for openness flexi spot did send this desk out for evaluation however as you need to know by now does not impact my evaluation in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping until completion of April at the earliest the desktop is an inch thick but it’s this basic laminate as you can possibly get doing not have even any cable grommets for travel through the outdoors container
for the desktop was not harmed in any way which is utterly strange because I could shoot a 30-second b-roll montage of just the damage and flaws on this desktop scuffed scraped pitted just incredibly rough male if I had purchased this I ‘d have been on the phone with customer support instantly they did likewise handled to miss out on drilling the pilot holes where you can connect the control box to the desktop a lot of needing to do that myself without accidentally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface area to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was really pretty uncomplicated the whole thing came together in about 45 minutes and despite the fact that there’s cables going to it from each component to support motorized function unusually absolutely where any kind of cable management products whatsoever the frame on this unit is a single motor double phase style versus the double motor three-stage design that comes requirement with the uplift desk this can be updated too to both the double stage double motor and a three-stage dual motor which presses the expense of the desk up
an additional 70 dollars the frame is created for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from just under 28 inches to just over forty seven point six inches so a max I ‘d it is more than high adequate even for me and I stay at 6 foot for this model does come basic with the control panel that permits up-and-down movement plus three memory spots with an LED readout to tell you the desk height the single motor style utilizes this drive shaft assembly which has to be adjusted as the width of the desk is changed the motor operation itself while it might be slow is extremely quiet as in barely audible this outside a cost would be the one benefit I would offer this unit over the uplift desk and I want to be careful here because this isn’t a hit piece this desk is 240 dollars more affordable than the equivalent uplift design over 35% less expensive even if you update this flexi area test to the dual motor three-stage design it still is available in a hundred and seventy dollars more affordable than the uplift but cheaper does not indicate inexpensive this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is strong even if max height I’ll certainly offer it that but the lateral stability of this desk the horizontal movement at this rate point it’s inappropriate it’s add fuel to the fire here they consist of a little safety baffle this little steel piece that installs to the frame and covers a part of this turning driveshaft when
this desk sees any lateral motion at all the drive shaft hits this baffle and the sound is definitely frustrating to leading things off I decided to add rolling casters to this desk this was a $30 upgrade and two of those 4 casters got here harmed also my prepare for this desk at this point is to lose the desk top and featured entirely and change it with a white laminate lemon table from Ikea and use it as an adjustable picture table which you can’t do this frame will accommodate desktops approximately 63 inches wide and 31 and a half inches deep so this will roll around the studio make it simpler to movie products without having to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift first that is an investment in quality workplace furnishings that will last you this at best seems like a cheaper imitation of that it simply doesn’t feel quality and the difference between this desk and my main desk is night and day do do not hesitate to check out their site also which also feels eerily similar to among their competitors there’s a wealth of devices you can get for the flexi area desk as much as and consisting of a foot massager and even a fixed stationary bicycle and I could spend another 10 minutes of our valuable time covering various options and devices I could however I believe I’m happier that they only sent out a basic desk since as a standard desk I’m not a fan of the quality control at this rate point and I do not believe slapping on a bunch of extras is the move when the core item isn’t what it should be they do provide a 30-day trial if you’re simply morbidly curious and they guarantee their desks for 3 years very desk is 5 years and uplift desk is 7 years if you are Flexispot M4 Xl Corner Sit-stand Desktop Work Station
in the market for a sit-stand desk they’re remarkable mine’s been a life changer for me both in regards to video gaming and efficiency however I would spend the money it’s gon na require to enter a higher end maker like uplift desk or very desk and I have not personally utilized extremely desk products so I can’t speak on it however their track record is very good huge thanks to flexi area for sending this out for review regrettably I can not recommend this system and for the record I’m a hundred percent sure they would have happily replaced the parts that I had a concern with seeing as how both the desktop and the casters got here harmed however from a consumer perspective you ‘d most likely be truly delighted to get this in