Flexispot Standing Desk Review …Flexispot, Memphis, Tn…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are minimal, here are a couple of features that I wasn’t necessarily a big fan of:
The package that the desk came in was heavy, so bringing it inside was a group effort, but this is just a repercussion of how tough the Flexispot is.
The practical cable tray was a bit complicated to install. In the end, you eventually slip it under screws, which wasn’t extremely clear from the directions.
You will need to purchase an anti-fatigue mat to stay comfortable, however this is an excellent idea for any standing desks, so I can’t fault Flexispot for that.
When it got here and I saw how heavy it was, I was both ecstatic (considering that this implied it was going to be sturdy) and also a little hesitant (since all of us know just how much of a challenge putting together furniture can be).
Fortunately, with the help of a training YouTube link, it took me only around 42 minutes to assemble. Scratch that, it took my 11-year-old daughter, with some supervision from me, from start to finish. The only hang-up I have with assembly was the cable tray, which I found wasn’t discussed well in the instructions.
Once assembled, I like the smooth appearance of this desk. I’m positive any of the many varied finishes that it comes in would look great in any workplace, and the adjustable width makes it simple to fit it in even the tiniest of office.
The peaceful operation and height memory settings make it easy, efficient, and peaceful to change in between sitting and standing as many times as you desire throughout the day.
This desk is sturdy. It can hold up to 335 pounds even while in operation, so if you have a significant desktop computer (or wish to take a nap on it for some reason) it has you covered. It will likewise equally disperse weight no matter how out of balance the weight you put on it is, it will not wiggle or wobble.
because video is quite kitted out as the desk we’re taking a look at today is quite standard I tried to get as near that as I might on uplifts site with equivalent configurations the flexi area desk we’re looking at today will run you about four hundred and ten dollars versus 6 hundred and fifty for a comparable desk from uplift I attempt to get as close as possible with the uplift design is in fact 5 inches longer but you can do a lot with five inches boom yes now for transparency flexi area did send this desk out for evaluation but as you should understand by now does not impact my evaluation in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not delivering until completion of April at the earliest the desktop is an inch thick however it’s this fundamental laminate as you can potentially get doing not have even any cable television grommets for travel through the outdoors carton
for the desktop was not damaged in any way which is entirely bizarre since I could shoot a 30-second b-roll montage of just the damage and flaws on this desktop scuffed scraped pitted simply very rough man if I had actually acquired this I ‘d have been on the phone with client service instantly they did likewise managed to miss out on drilling the pilot holes where you can connect the control box to the desktop a great deal of needing to do that myself without accidentally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was actually pretty straightforward the whole thing came together in about 45 minutes and despite the fact that there’s cables running to it from each part to support motorized function unusually definitely where any kind of cable management products whatsoever the frame on this unit is a single motor dual phase design versus the dual motor three-stage style that comes requirement with the uplift desk this can be updated also to both the double phase double motor and a three-stage dual motor which pushes the cost of the desk up
an extra 70 bucks the frame is designed for a max load of 154 pounds and it moves at a rate at an inch per second the height can vary from simply under 28 inches to just over forty seven point six inches so a max I ‘d it is more than high enough even for me and I stay at 6 foot for this model does come standard with the control board that permits up-and-down movement plus three memory spots with an LED readout to inform you the desk height the single motor design utilizes this drive shaft assembly which needs to be adjusted as the width of the desk is changed the motor operation itself while it might be slow is very peaceful as in barely audible this outside a price would be the one benefit I would offer this unit over the uplift desk and I want to be careful here because this isn’t a hit piece this desk is 240 dollars less expensive than the equivalent uplift design over 35% less expensive even if you update this flexi spot test to the dual motor three-stage design it still can be found in a hundred and seventy dollars cheaper than the uplift but cheaper does not suggest inexpensive this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is strong even if max height I’ll definitely give it that however the lateral stability of this desk the horizontal motion at this price point it’s undesirable it’s add fuel to the fire here they include a little safety baffle this little steel piece that installs to the frame and covers a portion of this turning driveshaft when
this desk sees any lateral motion at all the drive shaft hits this baffle and the sound is definitely infuriating to top things off I chose to add rolling casters to this desk this was a $30 upgrade and 2 of those four casters got here damaged also my plan for this desk at this moment is to lose the desk top and featured all together and replace it with a white laminate lemon table from Ikea and utilize it as an adjustable photo table which you can’t do this frame will accommodate desktops as much as 63 inches wide and 31 and a half inches deep so this will roll around the studio make it easier to movie items without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift first that is a financial investment in quality office furnishings that will last you this at best seems like a more affordable replica of that it simply does not feel quality and the distinction between this desk and my primary desk is night and day do do not hesitate to have a look at their website as well which also feels eerily similar to one of their competitors there’s a wealth of accessories you can get for the flexi area desk up to and consisting of a foot massager and even a fixed stationary bicycle and I could spend another 10 minutes of our precious time covering various choices and devices I could however I believe I’m better that they just sent out a standard desk since as a fundamental desk I’m not a fan of the quality control at this rate point and I do not think slapping on a lot of additionals is the move when the core product isn’t what it must be they do offer a 30-day trial if you’re simply morbidly curious and they guarantee their desks for 3 years extremely desk is 5 years and uplift desk is 7 years if you are Flexispot, Memphis, Tn
in the market for a sit-stand desk they’re remarkable mine’s been a life changer for me both in regards to video gaming and performance however I would spend the money it’s gon na require to enter into a higher end manufacturer like uplift desk or really desk and I haven’t personally utilized very desk products so I can’t speak on it however their track record is excellent big thanks to flexi spot for sending this out for review unfortunately I can not suggest this system and for the record I’m a hundred percent sure they would have gladly replaced the parts that I had an issue with seeing as how both the desktop and the casters showed up harmed but from a client standpoint you ‘d probably be actually delighted to get this in